Ultimate RX-7 Bit

N2Deep · #1 05-29-2004, 03:05 AM

hey everyone, it's been a long time since I posted anything up so here is some treat for everyone. Please let me know what you think.

included is: Mosfet mod, blue neon glow lights, deep dish racing rims with rotors, big exhaust pipe, special color effect, two speed, 200 mah battery upgrade, gold heatsink, 5.0 modified motor with light blue gear, rare earth magnet for steering, clear and lightened chasis, radio range enhancement on both RX and TX, lubricated axles, springs up front for bumps, and last but not least working headlights (HID blue).

N2Deep · #2 05-29-2004, 04:22 AM

Here's another look at the stuff being put into this car.

N2Deep · #3 05-29-2004, 04:32 AM

Here's another angle.

N2Deep · #4 05-29-2004, 11:17 AM

Last look before I sell the car to the highest bidder.....NOT!!!

Racer9 · #5 05-29-2004, 02:49 PM

No diff.?

MicroSpeed · #6 05-29-2004, 06:22 PM

WHOOOO!!! That is awe-some. It's about time someone shows a decent new modded car around here. That is very cool. Where did you get your 5.0 from? Do you have any chassis pictures (without the body). Looks cool so far.

filelicker · #7 05-29-2004, 09:05 PM

What did you rob those wheels and rotors off of?

dub city?

N2Deep · #8 05-30-2004, 01:54 AM

A pix of the inside will be taken and shown, as for the ball diff...it is currently on the Skyline but will show it in a pix-works very nice on tight corners and plus no rollover or skidding. The 5.0 motor is a prototype sent from a buddy of mine from China. I have only a few to try out since the motors are from a new phone offered in the far east. Very fast, in matter of fact...too fast with the fet mod. You almost need some wheelie bar for the car.

The clear chasis is from LXX-Perfection but the inner working parts are all modified. The chip is off from the AutoModellista set. This car has won me nomerous drag races to win other people's cars and even some cash.

MicroSpeed · #9 05-30-2004, 08:14 AM

cool, what are the specs on the skyline? Do you know what kind of phone the motor is from? And is the PCB from the BCG Auto Modellista or the LXX one?

Racer9 · #10 05-30-2004, 08:05 PM

Start selling the ball diffs! The car is very cool! The rims are awesome!

filelicker · #11 05-30-2004, 09:02 PM

Quote:

Originally posted by filelicker
What did you rob those wheels and rotors off of?

dub city?

in your previous post you answered every question but this one.

N2Deep · #12 05-31-2004, 01:51 AM

The rims are off Dub City new series. I got mine off from the red mazda rx-7, however there is also the blue and red ones available and they are on the Altezza. Best way to get the wheels out from the original axles is by twisting them loose. Then carefully using the right drill bit size and putting it on a hand held chuck, turn the drill till you go all the way through. This step is for front setup. As for the rears you have to use a drill bit that is just a smaller then the axle you are going to be using. You need to dab a small amount of 5 minute epoxy into the new whole and wipe off any access epoxy should it "bleed" out from the wheel. Make sure you don't drill all the way through the wheels that you are going to be using for the rear sets. To get a "true" spin on all four wheels, you are going to have to get something to spin the wheels and then drill it. Good luck on building yours.

filelicker · #13 05-31-2004, 09:34 AM

Thanks for the info , I use dubs wheels all the time except for the fronts I use the reversed pin style.Remove the pin and stick it back through the knuckles backside then trim a tiny bit off of the end of the axle pin and press on the wheel and you are done.

Racer9 · #14 05-31-2004, 12:20 PM

Show the diff!

Racer9 · #15 08-17-2004, 08:31 PM

any updates? i really want to see more of this great car!

and the diff.