TinyRC.com - XMODS, XMOD, Micro Flight, ZipZaps, ZipZaps SE, Bit Char-G, MicroSizers, TTTT, Plantraco Desktop Rover, SuperSlicks, Digi Q, Forums, News, Pictures, Parts, and Shop
Forums, XMODS, XMOD, Micro Flight, ZipZaps, ZipZaps SE, Bit Char-G, MicroSizers, TTTT, Plantraco Desktop Rover, SuperSlicks, Digi Q
XMODS Hop-Ups, XMODS Parts, XMOD Hop-Ups, XMOD Parts, Bit Char-G Hop-Ups, Bit Char-G Parts, MicroSizers Hop-Ups, MicroSizers Parts
  #1  
Old 12-16-2003, 11:03 AM
backtrack9's Avatar
backtrack9 backtrack9 is offline
sLoWly gOInG iNsAnE
 
Join Date: Dec 2003
Location: San Antonio, Texas
Posts: 9
Measuring Motor RPM

Ok everyone - has anyone found a good repeatable method for measuring the speed of these little motors? I am not talking about running it on a treadmill (very inacurate) to get the speed of the vehicle and then backing out the motor speed through calculations. The Tamiya speed checker is similar to this, but I am still leery about the results. I have been looking at using a technique outlined on the website by Roman Black - www.romanblack.com - showing how to measure the back EMF pulses from the motor over a given time period to indicate motor RPM. Also there is the method of measuring the current draw at various loads to calculate the motor's characteristics and then from these calculations use this motor as a generator when connected to a drive motor. This simply makes a dyno system with the test motor coupled to the generator motor. To test the speed, you would then connect the test motor to generator motor and only power the test motor and then measure the voltage created by the generator motor. This voltage is directly proportional to the speed of the generator motor shaft, which is the same speed as the test motor. The only problem is that this proportionality constant can only be found by first knowing the response of the generator motor at various RPMs. This means that you need to know an RPM to calculate an RPM. I'm sorry for such a long posting, but I am very frustrated at this point. As far as explanations are concerned, I can only explain things to a small degree - not much time - so please do some research before asking too many questions. I might be able to offer some links to motor theory and calculations. Thanks for your input.
Reply With Quote
  #2  
Old 12-16-2003, 02:48 PM
neurokinetik's Avatar
neurokinetik neurokinetik is offline
Mad Scientist
 
Join Date: Oct 2003
Location: Buffalo, NY
Posts: 901
I could design and build a tachometer, I just haven't felt like doing it yet. You could do it with an optical wheel, a slot-type optical sensor, and a couple of counter chips. Alternatively, they sell tachometers for model airplanes that read off of the propellors. Something like that could be made to work as well.
__________________
-- It is by will alone I set my mind in motion...

Last edited by neurokinetik; 12-16-2003 at 02:53 PM.
Reply With Quote
  #3  
Old 12-16-2003, 05:27 PM
TypeZer0's Avatar
TypeZer0 TypeZer0 is offline
0reZepyT
 
Join Date: Feb 2003
Location: Boston, MA
Posts: 804
this could work....for almsot the price of an xmod though http://www.allelectronics.com/cgi-bi...H-4&type=store
__________________
Friends (Joey's Bag)
Rachel: Exactly! Unisex!
Joey: Maybe you need sex. I had sex a couple days ago.
Rachel: No! No Joey! U-N-I-sex.
Joey: Well, I ain't gonna say no to that.
Reply With Quote
  #4  
Old 12-16-2003, 10:33 PM
neurokinetik's Avatar
neurokinetik neurokinetik is offline
Mad Scientist
 
Join Date: Oct 2003
Location: Buffalo, NY
Posts: 901
Nice find. I may end up picking one of those up.
__________________
-- It is by will alone I set my mind in motion...
Reply With Quote
  #5  
Old 12-18-2003, 11:14 AM
backtrack9's Avatar
backtrack9 backtrack9 is offline
sLoWly gOInG iNsAnE
 
Join Date: Dec 2003
Location: San Antonio, Texas
Posts: 9
One small word of caution

Thanks for the ideas everyone. Just one small word of caution about the laser tachometer method. These units require a reflective target be placed on the rotating shaft to be measured. These targets are sometimes as small as 1/8"X1/8" and sometimes as large as 3"x3". The higher quality tachometers (>$500) are the ones that can be used for smaller targets. I am not sure if the unit mentioned above requires such a large target or not. I think that for $50 it might be worth a test. One method to get around this would be to place a larger diameter adapter on the shaft of the motor so that you can use a larger target. Possibly this target adapter could be made out of plastic, wood or even rubber. Just something to put on the end of the shaft so that a larger target could be used. Thanks again for all of your help.
Reply With Quote
  #6  
Old 12-18-2003, 11:34 AM
neurokinetik's Avatar
neurokinetik neurokinetik is offline
Mad Scientist
 
Join Date: Oct 2003
Location: Buffalo, NY
Posts: 901
Well, I would just hook it up to a wheel that I swiped out of an arcade trackball. That's about 2" in diameter.
__________________
-- It is by will alone I set my mind in motion...
Reply With Quote
  #7  
Old 01-07-2004, 10:43 AM
backtrack9's Avatar
backtrack9 backtrack9 is offline
sLoWly gOInG iNsAnE
 
Join Date: Dec 2003
Location: San Antonio, Texas
Posts: 9
Laser Digital Tachometer

Ok, so I picked up one of these laser digital tachometers to see if they could indeed be used to measure the speed of these little motors. After placing a small target adapter on the end of the shaft of a Plasma Dash motor, I turn on the juice (2 AA batteries) and tested it out. The thing works like a champ. I just have to align it properly and I get a real-time RPM reading. AWESOME!!!!. Here is just a quick taste of some results for the Plasma Dash under no-load conditions: 20,580 rpm @ 2.56V (old/weak AA's). I measured the no-load current at 1.18A. This is exciting. Now I can quantify any gains made on motor modifications. I will try to measure some other motors and give results. I think Neuro will soon be able to provide the same info with his new o-scope. I just want to say thank you to TypeZero for the great heads-up on this useful little tool.
Reply With Quote
  #8  
Old 01-11-2004, 11:48 AM
nobodyhere962's Avatar
nobodyhere962 nobodyhere962 is offline
Honda 4 life
 
Join Date: Nov 2003
Location: Asia
Posts: 228
Send a message via AIM to nobodyhere962
off the topic but
when was xmod sci put up?
__________________
"Why do they have locks on the doors for stores that are open 24-7?"
that counts holidays too!

A new Question every year i think!
Reply With Quote
  #9  
Old 01-12-2004, 04:50 PM
suprafreak33 suprafreak33 is offline
got supra?
 
Join Date: Jul 2003
Location: Earth
Posts: 209
with in the last week
__________________
xmod
blue supra
6 cell
all upgrades[by rs]
Reply With Quote
  #10  
Old 01-12-2004, 05:00 PM
TypeZer0's Avatar
TypeZer0 TypeZer0 is offline
0reZepyT
 
Join Date: Feb 2003
Location: Boston, MA
Posts: 804
Re: Laser Digital Tachometer

Quote:
Originally posted by backtrack9
I just want to say thank you to TypeZero for the great heads-up on this useful little tool.
no prob. i was actually looking for this small gadget that i saw from Lego a year or two ago where it would measure the speed of the car you build by measuring the rotation of the shafts. coudln't find it so i started looking for small tachometers and came across that. glad it works well. maybe you coudl put up numbers on the motors you have and maybe we can compare it with neuro's measurements
__________________
Friends (Joey's Bag)
Rachel: Exactly! Unisex!
Joey: Maybe you need sex. I had sex a couple days ago.
Rachel: No! No Joey! U-N-I-sex.
Joey: Well, I ain't gonna say no to that.
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -5. The time now is 09:21 PM.


Powered by vBulletin® Version 3.7.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Mini Inferno Sale - Up to $85 Instant Savings!
Micro-T Hop-Ups
RC18R, M18, Micro RS4, Mini-LST, TamTech-Gear, Minizilla, RC18T, RC18B, RC18MT
shop.tinyrc.com Products
Tiny RC Community News
[03/17/10] Kyosho Mini-Z F1 MF-010 SP2... : The Kyosho Mini-Z F1 MF-010 SP2 Carbon Limited ASF 2.4GHz Tx-Less Chassis Set - more»
[10/23/09] Kyosho Mini-Z MR-03 In Stock! : The Mini-Z MR-03 (http://mr-03.com) is now In Stock and Pre-Orders are shipping! - more»
[09/06/09] Labor Day Savings - $5 Off... : Labor Day traditionally marks the unofficial end of summer - but we're not ready to let go! So, we - more»
Mini-Z, Mini-Z Racer, MR-02, MA-010
M18, M18T, RC18T, Mini-LST, Mini-T, Micro RS4, XRay, 1/18, 18th scale
XMODS, XMOD, Micro Flight, ZipZaps, ZipZaps SE, Bit Char-G, MicroSizers, TTTT, Plantraco Desktop Rover, SuperSlicks, Digi Q
Mini Inferno, Mini Inferno ST, half EIGHT, 1/16, 16th scale
Epoch, Indoor Racer, 1/43, 43rd scale
E-Savage, eSavage, eZilla, e-Zilla, HPI
Robots, Bots, Bipeds, Wheeled, Manoi, Roomba, NXT, Lego, Hacking
Crawling, Crawlers, Micro, RC, Losi Mini-Rock Crawler, Duratrax Cliff Climber
Kyosho Minium, Caliber 120, Minium Forums
Mini-Z Hop-Ups, Mini-Z Parts, Mini Inferno Hop-Ups, Mini Inferno Parts, M18 Hop-Ups, M18 Parts