TinyRC.com - Search Results

		TinyRC.com > Search Forums
Search Results

Showing results 1 to 17 of 17
Search took 0.07 seconds. Search: Posts Made By: cm961

Forum: Bit Char-G / MicroSizers

07-31-2003, 11:14 AM

Replies: 11

rcmart.com, anyone buy from here?

Views: 923

Posted By cm961

Whats the difference between a pull-back and a...

Whats the difference between a pull-back and a normal car?

Pete

Forum: Bit Char-G / MicroSizers

07-30-2003, 10:53 AM

Replies: 3

Alright Pimps, 4 those that missed out last time....

Views: 554

Posted By cm961

But not to Canada....

But not to Canada....

Forum: Bit Char-G / MicroSizers

07-30-2003, 09:47 AM

Replies: 4

MS $9.99 and free shipping

Views: 893

Posted By cm961

Damn, no shipping to Canada....

Damn, no shipping to Canada....

Forum: Bit Char-G / MicroSizers

07-29-2003, 09:56 AM

Replies: 14

Steering voltage

Views: 748

Posted By cm961

Oh and also I believe my motor works came with a...

Oh and also I believe my motor works came with a 120 or 140 mah battery in it. I believe most stock ones are 40 mah aren't they?

Pete

Forum: Bit Char-G / MicroSizers

07-29-2003, 09:56 AM

Replies: 14

Steering voltage

Views: 748

Posted By cm961

Yeah I've had trouble with the connections. The...

Yeah I've had trouble with the connections. The antennas on these clones ALWAYS come off, but thats no big deal. I find soldering the steering wires a pain because I can never get them to grab,...

Forum: Bit Char-G / MicroSizers

07-28-2003, 11:56 AM

Replies: 4

Single/Multi coil steering columns

Views: 1,707

Posted By cm961

Single/Multi coil steering columns

Hey Guys,

A few questions.

On cars with the single steering coil in the center versus two on the sides, the electro-magnetic attraction is done by reversing the polarity on the coil. This...

Forum: Bit Char-G / MicroSizers

07-28-2003, 08:46 AM

Replies: 14

Steering voltage

Views: 748

Posted By cm961

I've traced the steering problem down to one of...

I've traced the steering problem down to one of manufacturing tolerance. If I leave the screw that holds the steering stuff together pretty lose, then the steering is fine. If its tight, then one...

Forum: Bit Char-G / MicroSizers

07-27-2003, 04:56 PM

Replies: 14

Steering voltage

Views: 748

Posted By cm961

Yeah the car pulls to one side way better than...

Yeah the car pulls to one side way better than the other. You can see that the magnet doesn't grab as good. I have two cars, one with the magnet in the middle and coils on the sides and one with...

Forum: Bit Char-G / MicroSizers

07-25-2003, 10:37 PM

Replies: 14

Steering voltage

Views: 748

Posted By cm961

Steering voltage

Hey guys,

I just measured the voltage going to the steering coil (its a clone with a single coil in the middle versus two on the sides) and I'm reading the full voltage one way but only a...

Forum: Bit Char-G / MicroSizers

07-25-2003, 06:48 PM

Replies: 4

Slight twist on Layman's dual/tri cell

Views: 1,367

Posted By cm961

Way to ruin a dream guys! I guess we all want...

Way to ruin a dream guys! I guess we all want speed for dragracing, or just because we can do it!

Forum: Bit Char-G / MicroSizers

07-25-2003, 04:24 PM

Replies: 4

Slight twist on Layman's dual/tri cell

Views: 1,367

Posted By cm961

Slight twist on Layman's dual/tri cell

Hey Guys,

I was reading through the bitscience Layman's mod dual cell and I was thinking about how those batteries are small but if you put too many you fry the board. Well, lets say you took 5...

Forum: Bit Char-G / MicroSizers

07-25-2003, 09:54 AM

Replies: 10

One shot turbo using a cap

Views: 782

Posted By cm961

Sorry guys didn't try this out yet, got...

Sorry guys didn't try this out yet, got sidetracked dual celling and trying different motors. I spent 7 hours on my bit last night and ended up back running it stock. Well I did switch the motor...

Forum: Bit Char-G / MicroSizers

07-24-2003, 01:28 PM

Replies: 8

quad cells safe?

Views: 1,286

Posted By cm961

The motor might be ok with quad cell, but its too...

The motor might be ok with quad cell, but its too much for the PCB (in general I would assume). So you need to do that transistor thing so that the board can run of normal, or slightly higher than...

Forum: Bit Char-G / MicroSizers

07-24-2003, 01:27 PM

Replies: 60

I have done the unthinkable!

Views: 2,161

Posted By cm961

I hooked up a motor directly to my variable DC...

I hooked up a motor directly to my variable DC power supply. I found that at about 6.5 or 7 volts you start to lose any gains. I think tri-cell is about the most you should run through these...

Forum: Bit Char-G / MicroSizers

07-23-2003, 10:17 PM

Replies: 10

One shot turbo using a cap

Views: 782

Posted By cm961

Well I'm going to investigate tomorrow and see...

Well I'm going to investigate tomorrow and see what I can come up with. I'll let you guys know how it comes along.

Forum: Bit Char-G / MicroSizers

07-23-2003, 06:26 PM

Replies: 10

One shot turbo using a cap

Views: 782

Posted By cm961

hmm true, I agree that its probably not feasible....

hmm true, I agree that its probably not feasible. However, what is an appropriate value of R to use? Assuming it was just the motor the cap was draining through... Perhaps a 3V cap could be like...

Forum: Bit Char-G / MicroSizers

07-23-2003, 01:02 PM

Replies: 10

One shot turbo using a cap

Views: 782

Posted By cm961

One shot turbo using a cap

Hey Guys,

Can anyone think of a way to hook up a capacitor in series with the motor when say reverse is pressed, but to have it out of circuit normally? Not sure how feasible this is, I'll have...

Showing results 1 to 17 of 17

Forum Jump

All times are GMT -5. The time now is 12:06 PM.