fastest engine!!
 

hey guys...

i just thought, since there's soo many different engines out there (endless oems, pagers, hot wheels kit racers, etc)... let's have a list of all of em and which one is the fastest?

so far i have 1.0 and 3.0 and one from radio shack...it's in the clear dome display....dunno what it's called....(red back)

3.0 seems to be the fastest that i have

the radio shack one seem to have lots of torque and it's very close to my 3.0...

Ive tried the 2.2, 2.6, QFM 3.8 and ZipZap Turbo and NOS motors in all of my cars. The NOS seems to be the fastest with the 3.8 coming in second.

Barry

the nos motor is that good?

where do u buy that motor? i heard soemthing about the fast and furious kit ??? where do i get that?
can i just buy the motor? ...and lastly..how much??

heh...i was thinking of buying the hot wheels kit racing??? it's only 14 (canadian) dollars.... and i can use the batteries and engine...

You can pick up the F&F kit at Radioshack. I dont remember how much it cost ($15???) but you get a lot of stuff you can use other than the motor.

Oh and yes its pretty darn fast.

i always thought the 3.8 ruled them all....i havent checked out the NOS motor yet....i also find it funny that NOS makes nitrous oxide and zipzaps have a NOS motor

yea
 

I JSUT GOT IN MY 3.8 today i was hoping it would out run my zipzap motor but they are alomost exactly the same anybody else have their car doin the smae thing oh and also i hear some people talking about a green speed gearing for the bit and its not a zipzap thing its like a tomy thing anyone????

yea, the green gears are made for Bit Racers or, as it is known in the States, Hot Wheels K.I.T. Racers. They can be modified for Bit Char-gs with a litttle bit of cutting on the axle.

really?
 

hey datamonster thanks! i have a question though is there a HUGE difference does it ahve a higher topspeed then the bit char-gs or more torque can someone please explain thier results
thanks

Anyone have an easy way to get the ZZ motors in the Bits without breaking the back tab? (done it 2 times now...:()

well
 

well if first you dont succeed then......................



DONT TRY IT AGAIN

i figured it out finally a few days ago...

you have to take an exacto, and cut on inside bottom where the motor goes in....

err this isnt my picture, but i used it as an example of where to make some slight cuts
just trim away till it fits..it wont take long

Here is a little better picture I took about a week ago:

http://www.fordpower.net/hosted/microsizers/micro9.jpg

is the NOS engine faster than the 3.8 in acceleration, topspeed,.

and why are they faster in bits than zz

agghhh
 

ive said this some many tmes but its ok well the zipzap motors are faster in the bits because the zz motors are built to have more torque because they ahve to move a bigger car so zz motors get off the line well but against my 3.8 the 3.8 has a better top speed

i have a 1.0, 3.0,3.4darkside rotor, clone motor, zz turbo, zz nos. it seems that the 3.4 darkside rotor is as fast as my zz nos motor and the only difference is that the zz nos is loud and has beter acceleration and my 3.4 is not as loud and it is fast and smooter then my zz nos, but the acceleraction is not as good. my clone motor seems 2 also have good accelerationm its from a clone called 'Super Racing'. it dose a lil burn out before it goes, but it dont have good top speed. amd my zz turbo is simular 2 it.