TinyRC.com - XMODS, XMOD, Micro Flight, ZipZaps, ZipZaps SE, Bit Char-G, MicroSizers, TTTT, Plantraco Desktop Rover, SuperSlicks, Digi Q, Forums, News, Pictures, Parts, and Shop
Forums, XMODS, XMOD, Micro Flight, ZipZaps, ZipZaps SE, Bit Char-G, MicroSizers, TTTT, Plantraco Desktop Rover, SuperSlicks, Digi Q
XMODS Hop-Ups, XMODS Parts, XMOD Hop-Ups, XMOD Parts, Bit Char-G Hop-Ups, Bit Char-G Parts, MicroSizers Hop-Ups, MicroSizers Parts

Go Back   TinyRC.com > Blogs > Draconious

Rate this Entry

The MiX, Past Concepts...

Posted 05-31-2008 at 08:38 PM by Draconious
Updated 05-31-2008 at 08:56 PM by Draconious
I've always wanted to make an RC chassis to fit under 1:24 scale model bodies, until that idea became obsolete when I discovered the Mini-Z online one day. Then at least 7 years ago I was again motivated to make a chassis, to design a better Mini-Z. This is back when we only had the original MR01 chassis to tinker with, before the overland and F1 chassis, even before the X-mod. I wanted to make mine 4WD and get rid of the nit picky things the MR01 had; ground clearance, no servo saver, the motor being part of the rear suspension, bias differential, ability to tighten wheel nuts with out keeping the wheel from turning, less slop between parts, and lots of other nit picky issues I thought I could fix. I experimented with different ways to fit the parts under a Mini-Z body, this resulted in some very strange looking concept drawings.






These concepts proved I was not going to get the settings I wanted and the motor and batteries on the bottom which would have yielded the lowest center of gravity possible, since the batteries weigh more the motor wound up above the batteries in most of my “working” concepts.




Since I was slow working on my concepts, it was bound to happen an AWD chassis was announced, radio shack had released their X-mod chassis. At first I was disappointed and felt the X-mod would take away any need for an AWD Mini-Z so progress on my chassis slowed down even more, until I bought an X-mod and realized it was no threat due to its apparent slapped together rushed design resulting in a car with so many bad points that it was not race worthy. By this time the F1 and Overland were also out, the overland motivated me to design my chassis so it could support the truck bodies and higher ride height, thus seeding the desire to make my chassis an adaptable chassis. The Mini-Z Monster was released, and I discovered a simple conversion kit would allow use of the monster tires.





The release of the MR02 and wider bodies just added to the chassis settings my universally compatible chassis would require. Then came the Kyosho AWD Mini-Z, far better then the X-mod and equally as much of a buzz kill against progress of my chassis, however the cross compatibility of my chassis kept me motivated to continue its design… so I am still working on it, and the current version is actually very different then the last version above, in fact I went back to using a belt drive, but I will save that for the next blog post.
Total Comments 0

Comments

 
Recent Blog Entries by Draconious

All times are GMT -5. The time now is 08:02 PM.


Powered by vBulletin® Version 3.7.3
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
Mini Inferno Sale - Up to $85 Instant Savings!
Micro-T Hop-Ups
RC18R, M18, Micro RS4, Mini-LST, TamTech-Gear, Minizilla, RC18T, RC18B, RC18MT
shop.tinyrc.com Products
Tiny RC Community News
[03/17/10] Kyosho Mini-Z F1 MF-010 SP2... : The Kyosho Mini-Z F1 MF-010 SP2 Carbon Limited ASF 2.4GHz Tx-Less Chassis Set - more»
[10/23/09] Kyosho Mini-Z MR-03 In Stock! : The Mini-Z MR-03 (http://mr-03.com) is now In Stock and Pre-Orders are shipping! - more»
[09/06/09] Labor Day Savings - $5 Off... : Labor Day traditionally marks the unofficial end of summer - but we're not ready to let go! So, we - more»
Mini-Z, Mini-Z Racer, MR-02, MA-010
M18, M18T, RC18T, Mini-LST, Mini-T, Micro RS4, XRay, 1/18, 18th scale
XMODS, XMOD, Micro Flight, ZipZaps, ZipZaps SE, Bit Char-G, MicroSizers, TTTT, Plantraco Desktop Rover, SuperSlicks, Digi Q
Mini Inferno, Mini Inferno ST, half EIGHT, 1/16, 16th scale
Epoch, Indoor Racer, 1/43, 43rd scale
E-Savage, eSavage, eZilla, e-Zilla, HPI
Robots, Bots, Bipeds, Wheeled, Manoi, Roomba, NXT, Lego, Hacking
Crawling, Crawlers, Micro, RC, Losi Mini-Rock Crawler, Duratrax Cliff Climber
Kyosho Minium, Caliber 120, Minium Forums
Mini-Z Hop-Ups, Mini-Z Parts, Mini Inferno Hop-Ups, Mini Inferno Parts, M18 Hop-Ups, M18 Parts